Textured Pontoon Boat Carpet - 8.6 Foot Wide

Heads up:  Carpets are ordered on request and may take longer to arrive. Cancelled orders may be subject to a 15% restocking fee.

8-1/2' W Textured Pontoon Boat Carpeting

• 20oz cut-loop pontoon boat carpet is available in 8-1/2' width.
• Excess pontoon boat carpet can easily be trimmed with knife.
• Enter the number of feet needed in quantity box.
• 10 foot minimum.

Replacing More Than Just Your Pontoon Carpet?

PontoonStuff® created the idea of Pontoon Carpet Kits and Deck Kits to make your project easier. If you need more than just carpeting and plan on replacing your pontoon boat's deck, check out our Kits below:

• Pontoon Boat Carpet Kits - If you plan on buying plywood locally this kit comes with everything else you need.
• Pontoon Boat Deck Kits - If you cannot buy the correct marine plywood locally, the  Pontoon Deck Kit is for you.

Carpet Specifications

Cut Loop Berber Style Boat Carpet

• High quality, Berber style marine grade pontoon boat carpet.
• High quality, textured marine carpet with a mix of cut pile and looped carpet fibers.
• The textured look helps hide dirt and sand so your pontoon carpet appears clean.

Flexible Rubber Backing

• Our marine grade boat carpet has a marine rubber back that is designed to glued down to your pontoon boat's deck.

Cut Loop Marine Grade Carpet

Pontoon Boat Carpet Specifications

• Fiber: 100% UV Stabilized Polypropylene
• Denier:  2600
• Primary Backing: Woven Polypropylene
• Secondary Backing: SBR Marine Latex

Warranty

Worry-Free Marine Carpet Warranty

• PontoonStuff's pontoon boat carpet is covered by a 3 year warranty.
• Warranty covers any fading or deterioration to your carpet.
• Our pontoon carpet is designed to be glued completely to your pontoon's deck.
• If you do not use the recommended amount of glue your carpet will not stick.
• Use 1 gallon of glue for every 8' x 12' area of deck on your pontoon boat.

Installation

Care & Maintenance

Marine carpet is stain resistant & we recommend periodic vacuuming & cleaning with household detergents and warm water. Following these recommendations will help your boat carpet retain it's original appearance & prevent matting.

How To Replace Pontoon Boat Carpet

• Check out our pontoon forum for complete pontoon restorations and learn how to replace the deck and carpet on your pontoon.

Q: How do I install new carpet on my pontoon boat?

A: In order to install your boat carpet you must remove all of the old carpeting and adhesive from the deck of your pontoon.  Also, it is important to fill any voids or delaminated areas on your existing deck with wood putty or fiberglass filler.  If you do not remove the old carpet and glue or if you do not fill the voids in an existing deck you will feel the imperfections under the carpet and most importantly any left over adhesive may interact with the new glue, preventing it from bonding with the back of the carpet. 

If your deck is clean and the surface area is ready for the new carpet then read on, if you are having difficulty removing your old carpet please see below where we discuss the problems you may run into.

Before applying any glue to your deck roll your new pontoon carpet out completely over the deck of your boat so that you can inspect it.  Occassionally carpet will have imperfections in it which we may miss or it can get damaged in shipping, now is the time to discover any problems.  Do not glue your carpet down before you inspect it.  Call us immediately if you have any problems so that we can replace the carpet for you.  Once you have the carpet rolled out and it looks good, fold it in half the length of the deck.  For example, if you have a 20' pontoon boat, get in the front of the boat and fold the carpet over width wise and do the same in the back leaving a 4' wide by 20' long section of your deck exposed.  Your carpet will be folded on top of itself on the other side of the deck so that you can apply glue to half of the decking.  

By folding the carpet this way it makes installation much easier, you can apply the glue by standing on the side of the pontoon, without needing to get on your hands and knees.  Each gallon of glue will cover a 8' x 12' area, so if you have a 16-24' pontoon boat use one gallon per side, if you have a 25-30' pontoon you will need a total of 3 gallons of glue and will use 1-1/2 gallons per side.  Take your first gallon and dump it evenly across the explosed 4' x 20' wide section of the deck.  Using a medium nap paint roller spread the adhesive over the deck and make sure that there is full coverage with no empty areas.  Be sure to spread glue as far into the center when the carpet is flipped to one side so you don't end up with any areas that are not covered with the glue.  Once the glue is applied lay the carpet out over the entire deck and make sure it is flat and squared up.  You will not have much time to work with the carpet once you lay it on the glue, so be sure it is lined up on the deck properly before you begin applying the glue. 

Next you must compress the carpet onto the lines of glue.  The carpet backing is not smooth and has grooves and lines in it as well; the glue will be pressed into these areas forming a bond which will hold the carpet in place once the glue hardens.  Use a heavy roller, you can rent a carpet roller or use a heavy pipe to press the carpet down onto the glue.  This is the most important step, if you do not press the carpet down hard enough the glue and carpet backing will not bond together causing it to come up or creating lines and bubbles in the carpet.

Q: How do I remove the old carpet?  What if it doesn't come off easily or only comes off in small chunks?

A: If your pontoon boat is a 2000 model year or newer you may experience difficulty when removing the carpet.  Newer pontoon boats use a heavier carpeting and a stronger glue than was used in the 70's, 80's and early 90's.  Boat builders applied special marine adhesives that provide excellent adhesion and heavier backed carpeting than you see on the older model pontoons.  Also, since these boats are newer the carpet and glue have not deteriorated to the point where it is easy to remove them.  On most older pontoon boats the carpet will come off fairly easily with some scraping, cutting and tearing.  If you find that your pontoon carpet is only coming off in small chunks and that you cannot seem to remove the old adhesive and fibers you can try renting a floor sander or simply replace the decking. 

To remove the decking without taking up the carpet, if you choose to replace the flooring, here is how you do it.  First, find the seams where the plywood decking meet up, take a razor knife and cut across the floor separating the carpet on each sheet of plywood.  If the plywood deck is bolted down, cut the heads off the bolts under the deck and rip the decking off.  If the deck is screwed down, use a hole saw and locate the screw heads, cut around each head and tear the decking off.  Then use a sawzaw to remove the screws and plywood plugs that are left over.  You may find that the cost of the plywood is worth it compared to the time and energy you will spend trying to remove carpet that won't come off.